manualshive.com logo in svg

Cub Cadet Volunteer 4x4 Utility Vehicle, Shop Handbook, Page: 24 / 328

Share
Download
Cub Cadet Volunteer 4x4 Utility Vehicle Shop Handbook Download Page 24

Chapter 2- Drive System: CVT and Transfer Case

20

8.

Rod adjustment is made by lengthening or short-
ening the shift rods to make neutral at the Hurst 
gear selector lever correspond with neutral 
within the transfer case. See Figure 2.28.

8a.    The heavier rod that is connected to the 

shift arm nearest the engine controls for-
ward (high range), neutral, and reverse 
functions.   

8b.    Loosen the jam nut, then disconnect the 

rod to adjust it using a pair of 9/16” 
wrenches.  

8c.    Thread the rod-end up or down the length 

of the threads for adjustment.

8d.    The lighter rod that is connected to the shift 

arm farthest from the engine shifts the 
transfer case between neutral and low 
range forward.

8e.    Loosen the jam nut using a 1/2” wrench 

and a 7/16” wrench, then disconnect the 
transfer case end of the rod using a pair of 
1/2” wrenches. 

9.

Snug the jam nuts and remove the locking dowel 
after rod adjustment is completed.

10.

After the rod adjustment is done, operate the 
linkage to confirm that the shift forks move fully 
to their engaged detent positions.

•

If there is insufficient travel, the stops on the 
Hurst shift mechanism can be moved out.

•

If the linkages are over-throwing the shift fork 
travel, the stops on the Hurst shift mechanism 
can be moved in.

•

The stops are unlikely to need adjustment in the 
normal service life of the utility vehicle.  The 
most likely reason for the stops to be out of 
adjustment would be tampering by unqualified 
technicians. 

10.1. Remove the console cover / cup holder to gain 

access to the stop adjustments.                          
See Figure 2.29.

10b.  Remove the knob from the Hurst gear shift 

by turning it counter-clockwise.

10c.  Remove the grip from the differential lock 

control lever by pulling upward from the 
base of the grip.  A blow gun may be used 
to force the grip off of the lever by shoot-
ing compressed air into the hole at the top 
of the grip while lifting upward. 

Figure 2.28

Disconnecting linkage
to make low-range adjustment

Figure 2.29

Hurst shift
linkage 
exposed

Console cover /
cup holder 
removed

Summary of Contents for Volunteer 4x4 Utility Vehicle









































































































































































































































































































































Reviews:

No comments