manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 56 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 56

PN 50887-00   

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

48

SPECIFICATIONS

Section

8

NOTE

The 8 3/8” t-bolt clamps should be torqued to 8 ft lbs.

The 8 11/16” t-bolt clamps should be torqued to 12 
ft lbs.

 CHECKING BOLT TORQUE:

The table shown below is for reference purposes only and its use by anyone is entirely voluntary, unless otherwise 
noted. Reliance on its contents for any purpose is at the sole risk of that person. Crary Co. is not responsible for any 
loss claim or damage arising therefrom. In developing these tables, Crary has made a determined eff ort to present the 
contents accurately.

*Torque figures indicated above are valid for non-greased or non-oiled threads and heads unless otherwise specified.  Therefore, do not grease or oil 
bolts or cap screws unless otherwise specified in this manual.  When using locking elements, increase torque values by 5%.

*Torque value for bolts and capscrews are identified by their head markings.

ENGLISH

BOLT DIAMETER

BOLT TORQUE *

SAE 2

SAE 5

SAE 8

N.m

Ft-lb.

N.m

Ft-lb.

N.m

Ft-lb.

1/4”

7.5

5.5

11

8

16

12

5/16”

15

11

23

17

34

25

3/8”

27

20

41

30

61

45

7/16”

41

30

68

50

95

70

1/2”

68

50

102

75

149

110

9/16”

97

70

149

110

203

150

5/8”

122

90

203

150

312

230

3/4”

217

160

353

260

515

380

7/8”

230

170

542

400

814

600

1”

298

220

786

580

1220

900

1-1/8”

407

300

1085

800

1736

1280

1-1/4”

570

420

2631

1940

2468

1820

METRIC

BOLT DIAMETER

BOLT TORQUE *

4.8

8.8

10.9

12.9

N.m

Ft-lb.

N.m

Ft-lb.

N.m

Ft-lb.

N.m

Ft-lb.

M3

0.5

0.4

-

-

-

-

-

-

M4

3

2.2

-

-

-

-

-

-

M5

5

4

-

-

-

-

-

-

M6

6

4.5

11

8.5

17

12

19

14.5

M8

15

11

28

20

40

30

47

35

M10

29

21

55

40

80

60

95

70

M12

50

37

95

70

140

105

165

120

M14

80

60

150

110

225

165

260

190

M16

125

92

240

175

350

255

400

300

M18

175

125

330

250

475

350

560

410

M20

240

180

475

350

675

500

800

580

M22

330

250

650

475

925

675

1075

800

M24

425

310

825

600

1150

850

1350

1000

M27

625

450

1200

875

1700

1250

2000

1500

SAE 2

SAE 5

SAE
Grade
and
Head
Markings

BOLT DIAMETER

SAE 8

10.9

4.8

8.8

12.9

4.8

METRIC
Grade
and
Head
Markings

8.8

10.9

12.9

BOLT DIAMETER

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments