manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 24 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 24

PN 50887-00   

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

16

ASSEMBLY

4.4.1  LEFT HAND MOUNT

1.  Remove the existing OEM pin from the fore/aft cylinder, 

and discard.  Remove the reel stop bolt from the end of 
the reel arm and discard.  Remove the OEM hardware 
from the bottom of the OEM reel mounting bracket and 
discard hardware, except for the spacer.  The spacer 
will be re-used.

2.  Use a 3/8 x 5” bolt and nylock nut to secure the 3-3/4” 

nylon bearing to the LH reel mount (Figure 15). Nylon 
bearing should rotate freely.

3.  Slide the LH reel mount to the OEM reel arm.  Attach the 

LH reel mount to the OEM cylinder using a 5/8” x 3-1/4” 
bolt, 5/8” nylock nut and two 1/2” washers as shown in 
Figure 13. Use as many 5/8” washers as required to 
evenly space the cylinder in between the LH reel mount.

4.  Attach  the  bottom  of  the  LH  reel  mount  to  the  OEM 

reel arm using a 1/2” x 5-1/2” bolt, nut and washers.  
(Figure 14) 

5.  Attach the arm mount to the LH reel mount using two 

1/2”  x  4”  hex  bolts,  and  two  1/2”  nylock  flange  nuts.  
(Figure 15)

6.  Insert a reel mount into the arm mount and secure with 

a 1/2” x 2-3/4” bolt and 1/2” nylock flange nut.

7.  Install new cylinder mount using four 1/2” x 1” Torx bolts.  

The top hole will not be used on the LH side.

CAUTION

Be sure the reel is secure and will not move before be-
ginning installation.

4.4   REEL ARM MOUNT (FD1 & FD75 HEADERS)

Figure 13:  LH reel mount (FD1 & FD75 headers)

Figure 14:  LH reel mount (FD1 & FD75 headers)

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments