manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 53 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 53

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

45

SERVICE & MAINTENANCE

3.  Replace the drain plug.

4.  Fill the gearbox oil to recommended level through the 

top fill plug.

5.  Check  that  the  air  passage  through  the  vent  plug  is 

open.

6.  Dispose  of  the  used  oil  in  an  environmentally  safe 

manner.

GREASE:

  Use  an  SAE  multi-purpose  high  temperature 

grease with extreme pressure (EP) performance meeting 
or exceeding the NLGI #2 rating for all requirements. Also 
acceptable is an SAE multi-purpose lithium based grease.

GEARBOX LUBE:

  Use Mobilube SHC 75W-90 synthetic 

gear lube or equivalent with the following specifi cations: 

API Service GL-5/MT.1
MIL-L-2105D
MACK GO-J PLUS
SAE J2360
Capacity: 28 ounces (0.8 liters) 

STORING LUBRICANTS:

 Your machine can operate at 

top  effi  ciency only if clean lubricants are used. Use clean 
containers to handle all lubricants. Store them in an area 
protected from dust, moisture and other contaminants.

1.  Use  the  Maintenance  Checklist  provided  to  keep  a 

record of all scheduled maintenance.

2.  Use a hand-held grease gun for all greasing.

3.  Wipe grease fitting with a clean cloth before greasing 

to avoid injecting dirt and grit.

4.  Replace and repair broken fittings immediately.

5.  If fittings will not take grease, remove and clean thor-

oughly.   Also  clean  lubricant  passageway.  Replace 
fitting if necessary.

6.2   FLUIDS AND LUBRICANTS

6.3   GREASING

CHECKING THE GEARBOX OIL LEVEL

Check the gearbox oil level daily. Check more frequently if 
leaks exist around any of the plugs or shaft seals. 

When checking the oil on the gearbox be sure that the base 
of the gearbox is level.

6.4   GEARBOX OIL

Always  clean  the  vent  plug  if  any  leaks  are  noticed 
around shaft seals.

WARNING

CHANGING THE GEARBOX OIL 

See  Figure  55  for  the  location  of  oil  fi ll  and  drain  plugs.  
Every 500 operating hours or annually, whichever comes 
fi rst,  the  oil  should  be  replaced.  When  changing  the  oil, 
follow this procedure:
1.  Place a container under the gearbox.

2.  Remove the drain plug. Allow 10 minutes to drain.

Figure 55:  Gearbox oil plugs (Series II)

CHANGING THE GEARBOX SEALS 

1.  When changing the gearbox seals, use an 1/8” drill bit 

and drill a hole in the seal.

2.  Use a hook to pop seal out.

3.  Replace with new seal.

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments