manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 48 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 48

PN 50887-00   

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

40

OPERATION

5.3   PRE-OPERATION CHECKLIST

5.4.1  PRE-START INSPECTION

1.  Read the Operator’s Manual.

2.  Check that the hydraulic lines and electrical harnesses 

are routed where they will not contact moving parts.  Be 
sure all components are clipped, taped or tied securely 
in place.

3.  Check that all required nuts and bolts are installed and 

tightened to their specified torque.

5.4   MACHINE BREAK-IN

Effi  cient and safe operation of the CWS requires that each 
operator reads and understands the operating procedures 
and all related safety precautions outlined in this section.  
A pre-operation checklist is provided for the operator.  It is 
important for both personal safety and maintaining the good 
mechanical condition of the machine that this checklist is 
followed.

Before operating the machine and each time thereafter, the 
following areas should be checked off :
1.  Service the machine per the schedule outlined in the 

Service Record.

2.  Use only a combine of adequate power and specifica-

tions to operate the machine.

3.  Check that all guards are installed, secured and func-

tioning as intended.  Do not operate with missing or 
damaged shields.

4.  Ensure  that  the  machine  is  properly  attached  to  the  

header and that mechanical retainers, such as quick 
pins, are installed.

5.  Check the cutterbar, reel area and drives for entangled 

material.

6.  Check the chains and sprockets for proper tension and 

alignment. Adjust as required.

7.  Visually inspect the hydraulic system for leakage, loose 

fittings, and damaged hoses.  Tighten fittings, replace 
damaged components and wipe up leaked or excess 
hydraulic fluid.

8.  Check condition of driveline slip clutch friction discs.  

If installing replacement discs, adjust spring height to 
original height.  Deviation from original setting may be 
needed depending upon disc wear.  Run-in is recom-
mended  at  the  start  of  the  season  (see  Service  and 
Maintenance Section).

5.4.2  AFTER OPERATING FOR 2 HOURS

1.  Re-torque fasteners and hardware.

2.  Check that all safety decals are installed and legible.  

Apply new decals if required.

3.  Check  that  no  hydraulic  hoses  are  being  pinched, 

crimped, or are rubbing.  Reroute as required.

4.  Check  that  the  wiring  harness  is  not  being  pinched, 

crimped, or rubbing.  Reroute as required.

5.  Check the tension and alignment of all drive chains.  

Adjust as required.

6.  The gearbox will generate heat.  The typical operating 

temperature of the gearbox is 180° F.

5.4.3  AFTER OPERATING FOR 10 HOURS:

1.  Re-torque fasteners and hardware.

2.  Check that all guards are installed, secured and func-

tioning as intended.  Do not operate with missing or 
damaged shields.

3.  Check safety decals.  Install new ones if required.

4.  Check  the  routing  of  hydraulic  lines  and  the  wiring 

harness.    Reroute  as  required  to  prevent  pinching, 
crimping, binding, or rubbing.

5.  Refer to the normal servicing and maintenance sched-

ule as defined in the Service Record.

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments