manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 30 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 30

PN 50887-00   

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

22

CAUTION

Be sure the reel is secure and will not move before be-
ginning installation.

ASSEMBLY

4.5   REEL ARM MOUNT (FD70 & CIH 2162 HEADERS)

4.5.1  LEFT HAND MOUNT

1.  Assemble  the  bearings  using  the  spacer,  adaptor, 

bearing and washer.  Use a 3/8 x 5” bolt and nylock nut 
to secure the bearings to the CWS mount weldment.  
(Figure 26).

2.  Remove the OEM cylinder mount from the reel arm and 

discard.  Save the hardware for later use. (Figure 25)

3.  Set a CWS tube mount weldment on the OEM LH reel 

arm. Slide it back against the OEM bracket shown in 
Figure 24).

4.  Insert a 1/2” x 1-1/2” carriage bolt through the OEM 

bracket and the bottom hole of the CWS tube mount 
weldment. Install a 0.27” spacer on the bolt between 
the  CWS  tube  mount  weldment  and  OEM  bracket. 
Install a 1/2” washer and nylock nut on the end of the 
bolt. (Figure 24)

5.  Use the CWS tube mount weldment as a template to 

drill the top two holes through the reel arm bracket for 
3/8” bolts.

6.  Attach  the  CWS  tube  mount  weldment  to  the  OEM 

bracket  with  two  3/8”  x  1-3/4”  bolts  through  the  top 
holes. Install a .63” spacer on each bolt between the 
CWS tube mount weldment and OEM bracket. Install a 
nylock nut on each bolt and torque to 30 ft-lbs.

7.  Using a 1/2” x 3 1/2”  carriage bolt and locknut, attach 

an end hole of the arm mount tube to the clevis of the 
CWS tube mount weldment (Figure 26).

8.  Insert the reel mount assembly into the arm mount tube.

9.  Attach the adjustment strap to the arm mount tube and 

reel mount assembly with a 1/2” x 3-1/2” bolt, nut, and 
spacer.  (Figure 26)

10.  Attach the bottom end of the adjustment strap to the 

front hole of the CWS tube mount weldment with a 1/2” 
x 1-1/2” carriage bolt and nut.

11.  Install a new cylinder mount weldment to end of OEM 

real arm using the OEM hardware removed in step 2.

12.  Reconnect cylinder reusing the OEM hardware (Figure 

26).

Figure 23:  Bearing assembly (FD70 & CIH 2162 headers) 

Figure 24:  Left hand reel arm (FD70 & CIH 2162 headers)

Figure 25:  Bearing assembly (FD70 & CIH 2162 headers)

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments