manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 3 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 3

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

iii

NOTE

The  warranty  will  not  cover  gearboxes  that  have  been  disas-
sembled within the warranty period.

LIMITED WARRANTY

This warranty applies to all AG and Marine Equipment manufactured by Crary Industries.

Crary Industries warrants to the original owner each new Crary Industries product to be free from defects in material 
and workmanship, under normal use and service. The warranty shall extend as shown below from date of delivery. The 
product is warranted to the original owner as evidenced by a completed warranty registration on file at Crary Industries. 

THE WARRANTY REGISTRATION MUST BE COMPLETED AND RETURNED TO CRARY INDUSTRIES WITHIN 10 
DAYS OF DELIVERY OF THE PRODUCT TO THE ORIGINAL OWNER OR THE WARRANTY WILL BE VOID.

 

In the event of a failure, return the product, at your cost, along with proof of purchase to the selling Crary Industries dealer. 
Crary Industries will, at its option, repair or replace any parts found to be defective in material or workmanship. Warranty 
on any repairs will not extend beyond the product warranty.  Repair or attempted repair by anyone other than a Crary 
Industries dealer as well as subsequent failure or damage that may occur as a result of that work will not be paid under 
this warranty.  Crary Industries does not warrant replacement components not manufactured or sold by Crary Industries.

1.  This warranty applies only to parts or components that are defective in material or workmanship.  

2.  This warranty does not cover normal wear items including but not limited to bearings, belts, pulleys and reel tines.

3.  This warranty does not cover normal maintenance, service or adjustments.

4.  This warranty does not cover depreciation or damage due to misuse, negligence, accident or improper main-
tenance.

5.  This warranty does not cover damage due to improper setup, installation or adjustment.

6.  This warranty does not cover damage due to unauthorized modifications of the product. 

Crary Industries is not liable for any property damage, personal injury or death resulting from the unauthorized modification 
or  alteration  of  a  Crary  product  or  from  the  owner’s  failure  to  assemble,  install,  maintain  or  operate  the  product  in 
accordance with the provisions of the Owner’s manual.

Crary Industries is not liable for indirect, incidental or consequential damages or injuries including but not limited to loss 
of crops, loss of profits, rental of substitute equipment or other commercial loss.

This warranty gives you specific legal rights.  You may have other rights that may vary from area to area.

Crary Industries makes no warranties, representations or promises, expressed or implied as to the performance of its 
products other than those set forth in this warranty.  Neither the dealer nor any other person has any authority to make any 
representations, warranties or promises on behalf of Crary Industries or to modify the terms or limitations of this warranty 
in any way.  Crary Industries, at its discretion, may periodically offer limited, written enhancements to this warranty.

CRARY INDUSTRIES RESERVES THE RIGHT TO CHANGE THE DESIGN AND/OR SPECIFICATIONS OF ITS 
PRODUCTS AT ANY TIME WITHOUT OBLIGATION TO PREVIOUS PURCHASERS OF ITS PRODUCTS.

Product

Warranty Length

Finger Air Reel

2 year

Crary Wind System

2 year

Replacement Parts

90 days (unless superceded by warranty)

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments