manualshive.com logo in svg

Crary CWS CASE IH 2162, Owner'S Manual And Parts Manual, Page: 45 / 92

Share
Download
Crary CWS CASE IH 2162 Owner'S Manual And Parts Manual Download Page 45

PN 50887-00

Case IH 2162/MacDon FD1, FD70, FD75 Crary Wind System Owner’s/Parts

37

Section

OPERATION

5

Many  features  incorporated  into  this  machine  are  the 
result of suggestions made by customers like you.  Read 
this manual carefully to learn how to operate the machine 
safely and how to set it to provide maximum effi  ciency.  By 
following  the  operating  instructions  in  conjunction  with  a 
good maintenance program, your CWS will provide many 
years of trouble-free service.

The CWS is designed to dramatically improve harvesting 
effi  ciency. Be familiar with the machine before starting.

It is the responsibility of the owner or operator to read this 
manual  and  to  train  all  other  operators  before  they  start 
working  with  the  machine.  Hazard  control  and  accident 
prevention are dependent upon the awareness of personnel 
involved in the operation of the CWS.

Follow all safety instructions exactly.  Safety is everyone’s 
business.  By following recommended procedures, a safe 
working environment is provided for the operator, bystand-
ers and the area around the work site.  Untrained operators 
are not qualifi ed to operate the machine.

WARNING

1.  Read and understand the Owner’s Manual and all 

safety signs before servicing, adjusting or repairing.

2.  Install  and  secure  all  guards  and  shields  before 

starting or operating.

3.  Keep hands, feet, hair and clothing away from all 

moving and/or rotating parts.

4.  Place all controls in neutral or off, lower header to 

the ground, stop combine engine, set parking brake, 
chock wheels, remove ignition key and wait for all 
moving  parts  to  stop  before  servicing,  adjusting, 
repairing or unplugging.

5.  Clear the area of bystanders, especially small chil-

dren, before starting.

6.  Keep all hydraulic lines, fittings, and couplers tight 

and free of leaks before and during use.

7.  Clean reflectors and lights before transporting.

8.  Review safety related items annually with all person-

nel who will be operating or maintaining the machine.

9.  Shut the combine off when connecting the machine 

hydraulics.

10.  Do not exceed fan speed of 5300 RPM.  Check the 

fan speed by multiplying the driveline speed (RPM) 
by the gear ratio of the gearbox.

11.  Do not run the fan without back pressure.  Close the 

butterfly valve on the fan if the flex hose is discon-
nected.

Summary of Contents for CWS CASE IH 2162





























































































Reviews:

No comments