COP Security 15-CD52WI Installation And Operation Manual Download | Manualshive

Page: 46 / 55

background image

High Speed Dome Camera Introduction Manual

45

▌▌

PATTERN

The dome supports 4 pattern tours and each pattern cover at
most 10 Minutes of 500 commands. Please check the
following steps to set up a pattern.

1. PATTERN NO.:

Move the cursor here and press IRIS OPEN to enter the
setup of Pattern Number. Move the joystick to select a
pattern number (14) and press IRIS OPEN to confirm.

2. TITLE:

Move the cursor here and press IRIS OPEN to enter the
setup of Pattern Title. Check the detailed above in DOME
TITLE settings.

3. <SET>:

Move the cursor here and press IRIS OPEN to enter.
Move the dome up/down/left right, make the zoom in/out
and press IRIS OPEN to save the pattern tour.

4. START:

Move the cursor here and press IRIS OPEN to start the
current pattern tour.

5. DELETE:

Move the cursor here and press IRIS OPEN to delete the
current pattern tour.

«
...
44
45
46
47
48
...
»

Summary of Contents for 15-CD52WI
























































Reviews:

No comments

Related manuals for 15-CD52WI

Brand: D-Link Pages: 2

SMARTCAM SNH-1011N

Brand: Samsung Pages: 2

Magnum Alert-700

Brand: NAPCO Pages: 52

Brand: HOME8 Pages: 4

Brand: Call Aid UK Pages: 2

Brand: Ganz Pages: 2

fontastic Series

Brand: D-Parts Pages: 2

Brand: Varex Imaging Pages: 60

Brand: Feig Electronic Pages: 12

Brand: Zip Pages: 14

IDIS DC-D4517RXP

Brand: Direct IP Pages: 35

WAT-902H3 SUPREME

Brand: Watec Pages: 2

Brand: Dante Pages: 13

Brand: Steren Pages: 20

Brand: Identivision Pages: 61

Brand: Alean Pages: 29

Brand: SAFERA Pages: 5

Brand: DynaColor Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands