manualshive.com logo in svg

COP Security 15-CD52WI, Installation And Operation Manual, Page: 35 / 55

Share
Download
COP Security 15-CD52WI Installation And Operation Manual Download Page 35

                                                                                                     

        High Speed Dome Camera Introduction Manual

 

34

▌▌

SOFT LIMIT 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The user can set up the soft limit to define the left and right boundaries 

for the pan movement. 

 

SOFT LIMIT: Move the cursor here and press IRIS OPEN to enter. Move 

the joystick to select 

“ON” or “OFF” to enable or disable this function

.

 

1. LEFT LIMIT:  

Move the cursor here and press IRIS OPEN to enter. 
Now the user can mover the joystick to control the PAN 
movement of the dome to a defined position for the left 
limit. Press IRIS OPEN to confirm. 
 

2. RIGHT LIMIT:  

Move the cursor here and press IRIS OPEN to enter. 
Now the user can mover the joystick to control the PAN 
movement of the dome to a defined position for the right 
limit. Press IRIS OPEN to confirm. 

 
3. LIMIT DELETE:  

Move the cursor here and press IRIS OPEN to delete all 
the settings. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for 15-CD52WI
























































Reviews:

No comments