Comdial Conversip EPI00G-I12 User Manual Download Page 61

Page: 61 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

4.6 Transferring Calls

There are 5 different transfer options available:

• screened transfer—you announce the call prior to transfer,
• unscreened transfer—you transfer without a call announce,
• hot transfer—call announce prior to transfer, receiving party

does not have to pick up handset (for hands-free users),

• quick transfer (with call announce)—automatic transfer and call

announce without pressing TRNS/CONF, and

• quick transfer (without call announce)—automatic transfer, no

call announce, without pressing TRNS/CONF.

The following table summarizes each option and the situation for
which it is best suited.

Call Transferring Summary

Transfer

Option

Best Suited

For

Sender’s Actions
After Answering

Original Call

Delivery Method

of Transferred

Call

Screened
Transfer

Normal trans-
fers that
require intro-
duction.

1. Press TRNS/CONF
2. Dial Extension
3. Announce Call
4. Disconnect

Normal intercom
ringing (two short
bursts) and the
introduction of the
call; if answered in
speakerphone
mode, ringing also
follows the trans-
fer.

Unscreened
Transfer

Expected
transfers that
need no intro-
duction.

1. Press TRNS/CONF
2. Dial Extension
3. Disconnect

Normal intercom
ringing (two short
bursts).

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands