Comdial Conversip EPI00G-I12 User Manual Download Page 99

Page: 99 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

7.11 Programmed Button Display

7.11.1 BUTTON FUNCTIONS DISPLAY (BUTTON
QUERY)

You can cause the display to identify the function of each button on
your endpoint.
To button query your endpoint, perform
the following steps.

1. Select

OPTIONS

2. Select

Programming

3. Select

NEXT

until the Button

Query option appears.

4. Select

Button Query

5. Press the button in question. The

system displays the information
and holds for few seconds before the endpoint returns to idle.

7.11.2 STATUS OF BUSY LINES AND STATIONS
(BUSY DSS/BLF BUTTON INQUIRY)

You can use this feature to identify the station that is busy on a line or
the line on which a station is busy.

To identify the station that occupies a busy line, press the DSS/BLF
button for busy line. The system displays the intercom number of
station that is busy on line.

To identify the line that a busy station occupies, press a DSS/BLF
button for the busy station. The system displays the busy station’s
line number.

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands