Comdial Conversip EPI00G-I12 User Manual Download Page 135

Page: 135 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

135

Subdued Off-Hook Voice Announce (SOHVA)

A private announcement that can be made to a busy party which they
hear through the receiver of their handset.

System Alarm Reporting

Allows you to view (through the LCD telephone screen) the various
system alarms and the stations with which those alarms are asso-
ciated.

System Speed Dial

System speed dialing provides system users with a repertory of up to
500 numbers that they can dial from any telephone in the system. The
installer or the attendant is responsible for storing the system speed
dial numbers.

TAP (Flash/Recall)

Depending on your system’s programming, this button gives you a
fresh dial tone or activates a hook flash.

Toll Restriction

Class of service feature by which the system allows or denies out-
going calls to selected users over selected lines.

Tone Call

A ringing intercom call.

Tracker Pager

The Tracker optional pager system allows you to send and receive
messages to Tracker pagers assigned to station extension numbers.

TRNS/CNF

A fixed feature button that allows you to transfer outside calls and set
up conference calls.

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands