Comdial Conversip EPI00G-I12 User Manual Download Page 87

Page: 87 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

To enable DND, proceed as follows.

1. Select

OPTIONS

2. Select

Programming

3. Select

Do Not Disturb

4. Select Do Not Disturb interact

button to toggle between

and

OFF

5. Select

EXIT

To disable the DND condition,
REPEAT the previous procedure, but select

OFF

instead of

step 4.

To set a Do Not Disturb condition at
your endpoint when a call rings at your
station, perform the following steps.

1. Hear ringing and notice the

incoming call information in dis-
play.

2. Select

OPTIONS

3. Select

Programming

4. Select

Do Not Disturb

5. Select the

Do Not Disturb

inter-

act button. Ringing stops, the caller hears the do not disturb
tone, and your endpoint remains in DND until you disable the
feature.

6. Select

EXIT

7.4 Automatic Redial

If your station has the multiple automatic redial feature enabled, you
can place up to ten numbers in your endpoint’s redial queue.

Note

: The AUTOMATIC REDIAL button must be programmed by

your system installer or system administrator. Individual users can-
not program this feature.

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands