Comdial Conversip EPI00G-I12 User Manual Download Page 43 | Manualshive

Page: 43 / 140

background image

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

43

3.3 Automatic Dialing

This feature provides one- or two-button speed dialing using pro-
grammable buttons at which you have previously stored numbers.
Two levels of number storage are available at each storage location,
and you can use one or both levels as needed. Also, since you usually
store a line choice as part of a speed dial number, line selection is
automatic with speed dialing.

There are two types of speed dial numbers:

• numbers that you store for your own use (personal speed dial

numbers), and

• numbers that the system attendant stores for everyone’s use

(system speed dial numbers).

To use a programmed speed dial, press the programmed speed dial
button, or press

SHIFT

and programmed speed dial button.

To use a

personal speed dial number

, while on hook, dial the speed

dial number on the dial pad (

0

to

9

).

To speed dial a

system speed dial number

, while on hook dial

*

and

system speed dial number.

DSS/BLF Buttons:
Press button of desired
endpoint to dial directly.

Keypad:
Dial desired number for personal speed dial
OR
Dial * and number for system speed dial.

Speed Dial Options

«
...
41
42
43
44
45
...
»

Summary of Contents for Conversip EPI00G-I12













































































































































Reviews:

No comments

Related manuals for Conversip EPI00G-I12

Brand: Samsung Pages: 2

Brand: Barracuda Pages: 3

Brand: Samsung Pages: 34

Brand: NEC Pages: 24

Brand: VTech Pages: 31

Brand: AUDIOLINE Pages: 28

FortiVoice 50E6

Brand: Fortinet Pages: 22

XDECT 8315 Series

Brand: Uniden Pages: 44

Brand: AT&T Pages: 32

Brand: Curtis Pages: 4

Brand: BT Pages: 2

Brand: BELGACOM Pages: 34

antenna AN - 8630 - 25

Brand: Cobra Pages: 16

Brand: Brother Pages: 10

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 18

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands