Comdial Conversip EPI00G-I12 User Manual Download Page 83

Page: 83 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

To respond to an alert after it sounds,
choose one of the following.

• Select

CLEAR

to turn off the alert.

• Select

SET

to reset the alert for

the same time the following day.

6.5 Response Message Button

You may program a

RESPONSE MESSAGE

button, which allows you

to send an LCD message to a caller who has initiated a SOHVA or
intercom call from another EP100G-L12, or to send an LCD message
to another EP100G-L12/EP100G-I12 that you call and receive a busy
signal or no answer.

To store a fixed RESPONSE MESSAGE button (delivers the same
message each time it is pressed), perform the following steps.

1. Select

OPTIONS

2. Select

Programming

3. Select

NEXT

until the Feature Button option appears.

4. Select

Feature Button

5. Select the programmable button you wish to use as a response

message button.

6. Select

NEXT

until the Response Message option appears.

7. Select

Response Message

8. Select from the list of displayed messages. Select

NEXT

scroll through the list of messages. If you use the

Back at

Call

options add to them as follows:

• For the

Back at

message, dial the code for the time numbers

and colon from dialing codes table.

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands