Comdial Conversip EPI00G-I12 User Manual Download Page 91 | Manualshive

Page: 91 / 140

background image

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

91

3. If the called station does not answer or is busy, select

TRACK

.

4. Hear a confirmation beep (tracker page accepted) or hear busy

a tone (tracker page not accepted).

5. Press the

SPEAKER

button to end.

Note

: Tracker parked calls recall to your station after a pre-

programmed time-out. You can either place the call into
another Tracker page orbit or retrieve the call.

To retrieve a call that you parked using the Tracker option, perform
the following steps.

1. Press

HOLD

button to scroll your held calls (display shows

PAGE

and extension number of each parked call).

2. Press

TAP

to retrieve the displayed parked call.

If you receive a parked call message on your Tracker pager, perform
the following steps.

1. Go to any system station.
2. Press

INTERCOM

.

3. Dial the Tracker pager orbit code (

#800

to

#899

).

4. Retrieve the call.

To enable or disable a Tracker pager at your station, perform the fol-
lowing steps.

1. Press INTERCOM.
2. Dial

#07

to enable, or dial

#06

to disable.

3. Press

SPEAKER

to end.

7.6 Auxiliary/Headset Jack

The EP100G-L12 speakerphone is equipped with an auxiliary jack
that provides an interface for a headset, a tape recorder, an external
ringer, or an external pager. You must program one of its program-
mable buttons to serve as an enable/disable button for each auxiliary
device you plan to connect. The system activates only the device that
it identifies in the display, and activates only one device at any time.

«
...
89
90
91
92
93
...
»

Summary of Contents for Conversip EPI00G-I12













































































































































Reviews:

No comments

Related manuals for Conversip EPI00G-I12

Univerge SV8100

Brand: NEC Pages: 8

Univerge SV8100

Brand: NEC Pages: 19

Univerge SV8100

Brand: NEC Pages: 9

Brand: Viking Pages: 2

Brand: TATA Motors Pages: 17

Brand: Extel Pages: 52

Brand: ESI Pages: 2

Brand: Witech Pages: 24

Brand: Aastra Pages: 9

Brand: FunkTronic Pages: 23

Brand: LG Pages: 75

Brand: LG Pages: 138

Brand: LG Pages: 36

Brand: LG Pages: 46

Brand: LG Pages: 21

Brand: LG Pages: 18

Brand: LG Pages: 19

Brand: LG Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands