Comdial Conversip EPI00G-I12 User Manual Download Page 97

Page: 97 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

7.9.4 SETTING HEADSET VOLUME LEVEL

There are eight headset loudness levels that you can set for the current
call. While on a call and in headset mode, press the

VOLUME UP

VOLUME DOWN

button once for each change in loudness that you

desire.

7.9.5 SETTING GROUP LISTENING VOLUME LEVEL

There are eight group listening loudness levels. To set the level for
the current call, while on a call and in the group listening mode, press

VOLUME UP

VOLUME DOWN

button once for each change in

loudness you desire.

7.9.6 SETTING BACKGROUND MUSIC VOLUME
LEVEL

There are eight background music loudness levels. To set the level,
while background music is on at your station, press the

VOLUME UP

VOLUME DOWN

button once for each change in loudness you

desire. This level remains set for background music until you change
it again, even if you turn off the feature and then reactivate it.

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands