Comdial Conversip EPI00G-I12 User Manual Download Page 17

Page: 17 / 140

EP100G-L12 / EP100G-I12 User

Feb ‘05

Comdial

1.1 Speakerphone Buttons

Hold Button
(HOLD)

• Places a line or intercom call on hold.
• Stores pauses in number sequences during

programming.

• If available, scrolls through LCD response

messages.

• If multiple held calls feature is available,

scans or scrolls through calls placed on
hold (when hold light is flashing).

Interactive Buttons
(located below
alphanumeric
display)

• Provide quick and easy access to system

features.

• Provide straightforward button

programming without dialing codes (the
interactive buttons themselves, however,
are not programmable).

Intercom Button
(INTERCOM)

• Selects an intercom line.
• Allows you to initiate many of the

endpoint’s features.

Mute Button
(MUTE)

• Keeps the person on the line from hearing

your conversation.

• Allows reply to a Subdued Off-Hook Voice

Announcement (SOHVA).

Direct Station Select/
Busy Lamp Field
(DSS/BLF)
Programmable
Buttons

• Allow you to store numbers for automatic

dialing functions.

• Allow you to store extension numbers for

Direct Station Selection (DSS).

• May be programmed as a feature button.
• May be designated a line button by your

system installer.

Summary of Contents for Conversip EPI00G-I12













































































































































Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands

Comdial Conversip EPI00G-I12, User Manual

Search results

Summary of Contents for Conversip EPI00G-I12

Reviews:

Related manuals for Conversip EPI00G-I12

Brands by name

Popular brands