Chrysler 300 2018 Owner'S Manual Download Page 51 | Manualshive

Page: 51 / 485

background image

WARNING!

•

Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, exhaus-
tion or other physical condition must exercise care
when using the seat heater. It may cause burns even
at low temperatures, especially if used for long
periods of time.

•

Do not place anything on the seat or seatback that
insulates against heat, such as a blanket or cushion.
This may cause the seat heater to overheat. Sitting in
a seat that has been overheated could cause serious
burns due to the increased surface temperature of the
seat.

Front Ventilated Seats — If Equipped

Located in the seat cushion and seat back are fans that

draw the air from the passenger compartment and move

air through fine perforations in the seat cover to help keep

the driver and front passenger cooler in higher ambient

temperatures. The fans operate at two speeds, HI and LO.

The front ventilated seats control buttons are located

within the Uconnect system. You can gain access to the

control buttons through the climate screen or the controls

screen.

•

Press the ventilated seat button

once to choose HI.

•

Press the ventilated seat button

a second time to

choose LO.

•

Press the ventilated seat button

a third time to turn

the ventilated seat off.

NOTE:

The engine must be running for the ventilated seats

to operate.
Vehicles Equipped With Remote Start
On models that are equipped with remote start, the venti-

lated seats can be programmed to come on during a remote

start.
This feature can be programmed through the Uconnect

system. Refer to “Uconnect Settings” in “Multimedia” for

further information.

3

GETTING TO KNOW YOUR VEHICLE

49

«
...
49
50
51
52
53
...
»

Summary of Contents for 300 2018






































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2018

Brand: iDataLink Pages: 9

HOIST-A-TOP JL CRANK

Brand: Lange Originals Pages: 13

Brand: BrandMotion Pages: 8

Brand: Ford Pages: 37

1973 Crown Hardtop

Brand: Toyota Pages: 50

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

Brand: FAAFTECH Pages: 8

Brand: AutoMaxi Pages: 2

Brand: Ford Pages: 368

Brand: tams elektronik Pages: 44

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: Volvo Pages: 266

Brand: Fab Fours Pages: 13

Brand: Magneti Marelli Pages: 2

Brand: Subaru Pages: 32

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands