Chrysler 300 2018 Owner'S Manual Download Page 396

Page: 396 / 485

trees and road surfaces during other seasons are highly

corrosive to the metal in your vehicle. Outside parking,

which exposes your vehicle to airborne contaminants, road

surfaces on which the vehicle is operated, extreme hot or

cold weather and other extreme conditions will have an

adverse effect on paint, metal trim, and underbody protec-

tion.
The following maintenance recommendations will enable

you to obtain maximum benefit from the corrosion resis-

tance built into your vehicle.
What Causes Corrosion?
Corrosion is the result of deterioration or removal of paint

and protective coatings from your vehicle.
The most common causes are:

•

Road salt, dirt and moisture accumulation.

•

Stone and gravel impact.

•

Insects, tree sap and tar.

•

Salt in the air near seacoast localities.

•

Atmospheric fallout/industrial pollutants.

Body And Underbody Maintenance

Cleaning Headlights
Your vehicle is equipped with plastic headlights and fog

lights that are lighter and less susceptible to stone breakage

than glass headlights.
Plastic is not as scratch resistant as glass and therefore

different lens cleaning procedures must be followed.
To minimize the possibility of scratching the lenses and

reducing light output, avoid wiping with a dry cloth. To

remove road dirt, wash with a mild soap solution followed

by rinsing.
Do not use abrasive cleaning components, solvents, steel

wool or other aggressive material to clean the lenses.

Preserving The Bodywork

Washing

•

Wash your vehicle regularly. Always wash your vehicle

in the shade using Mopar Car Wash, or a mild car wash

soap, and rinse the panels completely with clear water.

•

If insects, tar, or other similar deposits have accumulated

on your vehicle, use Mopar Super Kleen Bug and Tar

Remover to remove.

394

SERVICING AND MAINTENANCE

Summary of Contents for 300 2018






































































































































































































































































































































































































































































































Search results

Summary of Contents for 300 2018

Reviews:

Related manuals for 300 2018

Brands by name

Popular brands

Chrysler 300 2018, Owner'S Manual

Search results

Summary of Contents for 300 2018

Reviews:

Related manuals for 300 2018

Brands by name

Popular brands