manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 8 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 8

WARNINGS AND CAUTIONS

This Owner’s Manual contains

WARNINGS

against op-

erating procedures that could result in a collision or
bodily injury. It also contains

CAUTIONS

against proce-

dures that could result in damage to your vehicle. If you
do not read this entire manual, you may miss important
information. Observe all Warnings and Cautions.

VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the
left front corner of the instrument panel, visible through
the windshield. This number also appears stamped on
the right sliding door sill under the sill moulding and
printed on the Automobile Information Disclosure Label
affixed to a window on your vehicle, the vehicle regis-
tration and title.

Vehicle Identification Number

6

INTRODUCTION

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments