manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 531 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 531

NOTE:

If either front tire is flat it may be necessary to

jack up the vehicle to remove the compact spare tire/
cover assembly from under the vehicle.

4. Stand the tire/cover assembly upright and remove the
wheel spacer by squeezing the winch retaining tabs
together. Push the retainer through the spare tire to
release it from the wheel.

Pulling Spare Tire

Removing Wheel Spacer

6

WHAT TO DO IN EMERGENCIES

529

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments