manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 245 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 245

Reprogramming A Single HomeLink

威

Button

To reprogram a channel that has been previously trained,
follow these steps:

1. Turn the ignition switch to the ON/RUN position.

2. Press and hold the desired HomeLink

威

button until

the indicator light begins to flash after 20 seconds.

Do not

release the button.

3.

Without

releasing

the

button

proceed

with

“Canadian/Gate Operator Programming” Step 2 and
follow all remaining steps.

Using HomeLink

姞

To operate, press and release the programmed
HomeLink

威

button. Activation will now occur for the

programmed device (i.e., garage door opener, gate opera-
tor, security system, entry door lock, home/office light-
ing, etc.,). The hand-held transmitter of the device may
also be used at any time.

Security

It is advised to erase all channels before you sell or turn
in your vehicle.

To do this, press and hold the two outside buttons for
20 seconds until the red indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.

The HomeLink

威

Universal Transceiver is disabled when

the Vehicle Security Alarm is active.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

243

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments