Chrysler 2012 Town & Country Owner'S Manual Download Page 310

Page: 310 / 652

•

Key not programmed

•

Vehicle Not in Park

•

Key Left Vehicle

•

Key Not Detected

•

Press Brake Pedal and Push Button to Start

•

Door(s) Ajar (with a single chime, if vehicle is in
motion)

•

Liftgate Ajar (chime will sound when vehicle starts
moving)

•

Low Tire Pressure

•

Service TPM System (refer to “Tire Pressure Monitor-
ing System” in “Starting And Operating”)

•

Turn Signal On

•

RKE Battery Low

•

Service Keyless System

•

LOW WASHER FLUID

•

Oil Change Required

•

Check Gascap

•

Left Front Turn Signal Light Out

•

Left Rear Turn Signal Light Out

•

Right Front Turn Signal Light Out

•

Right Rear Turn Signal Light Out

•

Park Assist Disabled

•

Service Park Assist System

•

Personal Settings Not Available — Vehicle Not in Park

•

Blind Spot System Off — This message is displayed
when the ignition is turned to ON to indicate the Blind
Spot System has been turned off.

308

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 Town & Country

Reviews:

Chrysler 2012 Town & Country, Owner'S Manual, Page: 310 / 652

Search results

Summary of Contents for 2012 Town & Country

Reviews: