Chrysler 2012 Town & Country Owner'S Manual Download Page 184

Page: 184 / 652

2. Return the head restraint to the upright position.

3. Pull up on the seatback recliner lever on the outboard
side of the seat to fold head rest and seatback and tumble
seat forward.

Easy Entry Second Row

The second row Stow ’n Go

威

seats allow easy entry to the

third row seat or rear cargo area.

Pull up on the seatback recliner lever on the outboard
side of the seat.

Raising The Head Restraint

Seatback Recliner Lever, Seat Tumble,

And Head Restraint Fold Lever

182

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 Town & Country

Reviews:

Chrysler 2012 Town & Country, Owner'S Manual, Page: 184 / 652

Search results

Summary of Contents for 2012 Town & Country

Reviews: