manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 364 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 364

Using The Touch-Screen Radio Controls

1. Press the MENU hard-key on the radio faceplate.

2. Touch the Rear VES soft-key to display the Rear VES
Controls. If a channel list is displayed, press the HIDE
LIST soft-key to display the Rear VES Controls screen.

3. Touch the 1 soft-key and then touch either AUX 1 or
AUX 2 in the VES column (depending which AUX input
is used). To exit press the back arrow soft-key at the top
of the screen.

Rear VES Soft-key

Select Channel/Screen 1 And

AUX 1 In The VES Column

362

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments