manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 497 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 497

WARNING! (Continued)

•

Guard against carbon monoxide with proper
maintenance. Have the exhaust system inspected
every time the vehicle is raised. Have any abnor-
mal conditions repaired promptly. Until repaired,
drive with all side windows fully open.

•

Keep the liftgate closed when driving your vehicle
to prevent carbon monoxide and other poisonous
exhaust gases from entering the vehicle.

FLEXIBLE FUEL — IF EQUIPPED

E-85 General Information

The information in this section is for Flexible Fuel ve-
hicles only. These vehicles can be identified by a unique
fuel filler door label that states

Ethanol (E-85) or Un-

leaded Gasoline Only.

This section only covers those

subjects that are unique to these vehicles. Please refer to

the other sections of this manual for information on
features that are common between Flexible Fuel and
gasoline-only powered vehicles.

E-85 Fuel Cap

5

STARTING AND OPERATING

495

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments