manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 190 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 190

Secure the retainer strap to the inside grab handle located
on the B-Pillar. When not in use, store the strap in the
sewn-in pocket located on the base of the seat cushion.

WARNING!

To reduce the risk of personal injury:

•

Retainer strap must always be securely attached to
grab handle when seat is folded forward and
vehicle is moving.

•

Never occupy the seat or the center seat behind a
seat that has been folded forward.

Retainer Strap

188

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments