Chrysler 2012 Town & Country Owner'S Manual Download Page 603

Page: 603 / 652

Chassis

Component

Fluid, Lubricant, or Genuine Part

Automatic Transmission

MOPAR

威

ATF+4

威

Automatic Transmission Fluid or equivalent licensed

ATF+4

威

product.

Brake Master Cylinder

MOPAR

威

DOT 3 and SAE J1703 should be used or equivalent. If DOT 3

brake fluid is not available, then DOT 4 is acceptable. Use only recom-
mended brake fluids.

Power Steering Reservoir

MOPAR

威

Power Steering Fluid +4, MOPAR

威

ATF+4

威

Automatic Trans-

mission Fluid or equivalent licensed ATF+4

威

product.

MAINTAINING YOUR VEHICLE

601

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 2012 Town & Country

Reviews:

Chrysler 2012 Town & Country, Owner'S Manual, Page: 603 / 652

Search results

Summary of Contents for 2012 Town & Country

Reviews: