manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 270 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 270

Position 2 shows the raised storage tray revealing a large
storage area below.

Dual Storage Bins

Position 3 shows the top portion of the console in a
rearward position. This is accomplished by lifting the
upper most latch at the front of the console. This provides
easy access to the storage area below and provides two of
the four cupholders for the second row passengers.

Console Position 2

Console Position 3

268

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments