manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 223 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 223

ParkSense

威

will retain the last system state (enabled or

disabled) from the last ignition cycle when the ignition is
changed to the ON/RUN position.

ParkSense

威

can be active only when the shift lever is in

REVERSE. If ParkSense

威

is enabled at this shift lever

position, the system will remain active until the vehicle
speed is increased to approximately 11 mph (18 km/h) or
above. The system will become active again if the vehicle
speed is decreased to speeds less than approximately
10 mph (16 km/h).

ParkSense

姞

Sensors

The four ParkSense

威

sensors, located in the rear fascia/

bumper, monitor the area behind the vehicle that is
within the sensors’ field of view. The sensors can detect
obstacles from approximately 12 in (30 cm) up to 79 in
(200 cm) from the rear fascia/bumper in the horizontal
direction, depending on the location, type and orienta-
tion of the obstacle.

ParkSense

姞

Warning Display

The ParkSense

威

Warning screen will only be displayed if

Sound and Display is selected from the Customer- Pro-
grammable Features section of the Electronic Vehicle
Information Center (EVIC). Refer to “Electronic Vehicle
Information Center (EVIC)/Personal Settings (Customer-
Programmable Features)” in “Understanding Your In-
strument Panel” for further information.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

221

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments