manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 356 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 356

NOTE:

The glove compartment will have a position

where the iPod

威

or consumer electronic audio device

cable can be routed through without damaging the cable
when closing the lid. This allows routing of the cable
without damaging it while closing the lid. If a cut out is
not available in the glove compartment, route the cable
away from the lid latch and in a place that will allow the
lid to close without damaging the cable.

Once the audio device is connected and synchronized to
the vehicle’s iPod

威

/USB/MP3 control system (iPod

威

or

external USB device may take a few minutes to connect),
the audio device starts charging and is ready for use by
pressing radio switches, as described below.

NOTE:

If the audio device battery is completely dis-

charged, it may not communicate with the iPod

威

/USB/

MP3 control system until a minimum charge is attained.
Leaving the audio device connected to the iPod

威

/USB/

MP3 control system may charge it to the required level.

Using This Feature

By using iPod cable or external USB device to connect to
USB port:

•

The audio device can be played on the vehicle’s sound
system, providing metadata (artist, track title, album,
etc.) information on the radio display.

•

The audio device can be controlled using the radio
buttons to Play, Browse, and List the iPod

威

contents.

•

The audio device battery charges when plugged into
the USB/AUX connector (if supported by the specific
audio device)

Controlling The iPod

姞

Or External USB Device

Using Radio Buttons

To get into the iPod

威

/USB/MP3 control mode and access

a connected audio device, either press the “AUX” button
on the radio faceplate or press the VR button and say

⬙

USB

⬙

or

⬙

Switch to USB

⬙

. Once in the iPod

威

/USB/MP3

354

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments