Chrysler 2012 Town & Country Owner'S Manual Download Page 31 | Manualshive

Page: 31 / 652

Chrysler 2012 Town & Country Owner'S Manual Download Page 31

3. Remove and replace the battery. When replacing the
battery, match the + sign on the battery to the + sign on
the inside of the battery clip, located on the back cover.
Avoid touching the new battery with your fingers. Skin
oils may cause battery deterioration. If you touch a
battery, clean it with rubbing alcohol.

4. To assemble the RKE transmitter case, snap the two
halves together.

General Information

This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received,
including interference that may cause undesired
operation.

If your RKE transmitter fails to operate from a normal
distance, check for these two conditions.

1. A weak battery in the RKE transmitter. The expected
life of the battery is approximately three years.

2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.

Separating RKE Transmitter

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

29

«
...
29
30
31
32
33
...
»

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments