manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 203 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 203

Customer-Programmable Features” in “Understanding
Your Instrument Panel” for further information.

TO OPEN AND CLOSE THE HOOD

To open the hood, two latches must be released.

1. Pull the hood release lever located on the instrument
panel, below the steering column.

2. Move to the front of the vehicle and look inside the
center of the hood opening. Locate, then push the safety
catch lever downward while raising the hood at the same
time.

Hood Release

Safety Catch Location

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

201

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments