manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 526 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 526

Spare Tire Removal

The spare tire is stowed inside a protective cover located
under the center of the vehicle between the front doors by
means of a cable winch mechanism. The “spare tire
drive” nut is located on the floor, under a plastic cap at
the front of the floor console or under front super console
forward bin liner.

To Access Spare Tire Winch Drive Nut

To access the spare tire winch drive nut and lower the
spare tire, you will need to refer to one of the following
center console configurations.

Super Console

For vehicles equipped with the Super Console, the spare
tire winch assembly drive nut is located beneath the
console.

Spare Tire Location

524

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments