manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 569 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 569

WARNING!

Do not remove the A/C air filter while the blower is
operating or personal injury may result.

The A/C air filter is located in the fresh air inlet behind
the glove box. Perform the following procedure to re-
place the filter:

1. Open the glove compartment and remove all contents.

2. Push in on the sides of the glove compartment and
lower the door.

3. Pivot the glove compartment downward.

4. Disengage the two retaining tabs that secure the filter
cover to the HVAC housing, and remove the cover.

5. Remove the A/C air filter by pulling it straight out of
the housing.

6. Install the A/C air filter with the arrow on the filter
pointing toward the floor. When installing the filter
cover, make sure the retaining tabs fully engage the
cover.

A/C Air Filter Replacement

7

MAINTAINING YOUR VEHICLE

567

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments