manualshive.com logo in svg

Chrysler 2012 Town & Country, Owner'S Manual, Page: 222 / 652

Share
Download
Chrysler 2012 Town & Country Owner'S Manual Download Page 222

To Accelerate For Passing

Press the accelerator as you would normally. When the
pedal is released, the vehicle will return to the set speed.

Using Electronic Speed Control On Hills

The transmission may downshift on hills to maintain the
vehicle set speed.

NOTE:

The Electronic Speed Control system maintains

speed up and down hills. A slight speed change on
moderate hills is normal.

On steep hills, a greater speed loss or gain may occur so
it may be preferable to drive without Electronic Speed
Control.

WARNING!

Electronic Speed Control can be dangerous where the
system cannot maintain a constant speed. Your ve-
hicle could go too fast for the conditions, and you
could lose control and have an accident. Do not use
Electronic Speed Control in heavy traffic or on roads
that are winding, icy, snow-covered or slippery.

PARKSENSE

姞

REAR PARK ASSIST — IF

EQUIPPED

The ParkSense

威

Rear Park Assist system provides visual

and audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. Refer to ParkSense

威

System

Usage Precautions for limitations of this system and
recommendations.

220

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2012 Town & Country













































































































































































































































































































































































































































































































































































































































































Reviews:

No comments