Carrier Access Adit 600 User Manual Download Page 194 | Manualshive

Page: 194 / 296

background image

7-8

CMG Router - Release 2.7

Verification Window

Trace Route

Method

<ICMP>

- Internet Control Message Protocol (ICMP) method of trace routing is the most

widely used and has the best reliability. (Default).

<UDP>

- User Datagram Protocol (UDP) method requires that all devices in the chain of the

trace route support probes on the particular UDP port. This method is not recommended.

Size

Define Packet Size. Range 0 - 65500

IP: Tos

Sets the IP type of service. Range 0x00 - 0xFF Hex. Default is 0.

Don’t Frag

Sets the "Don’t Fragment" flag in the IP header. This can be used along with the size setting to
determine the maximum payload size that can be sent between the router and the destination
without fragmentation occurring, the path MTU.

UDP Port

Sets the UDP port to send to. Range is 1 - 65535, with a default of 33434. This setting only
applies if the method is set to UDP.

Query: Number

Defines the number of probe packets sent to each hop along the route. Range is 1 - 10, with a
default of 3.

Wait

Defines the wait time between queries. Range is 0 - 250 ms. Default is 1 ms.

Timeout

Defines the query timeout. Range is 1 - 60 seconds. Default is 3 seconds.

«
...
192
193
194
195
196
...
»

Summary of Contents for Adit 600









































































































































































































































































































Reviews:

No comments

Related manuals for Adit 600

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP Pages: 14

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

Brand: Aztech Pages: 2

Brand: US Robotics Pages: 36

Brand: ZyXEL Communications Pages: 485

Brand: ICP DAS USA Pages: 8

Brand: Idis Pages: 85

Brand: TP-Link Pages: 2

Brand: Hamlet Pages: 122

Brand: Tripp Lite Pages: 2

Brand: Keysight Technologies Pages: 106

Brand: Amit Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands