Carrier Access Adit 600 User Manual Download Page 168

Page: 168 / 296

5-36

CMG Router - Release 2.7

Profile Directory:Remote Profile

Filter Network/Server

NOTE:

The server type 0004 was selected to be advertised to the LAN, therefore

all 0004 type servers will be advertised and do not need to be individually selected
(lines 2 through 4).

If the server type and name are specified, only servers that match both values will be learned or
filtered. Be aware that the

Name

value is case and spacing sensitive.

Network

This field displays the network address of each service/network learned from the remote unit.
If this route was added using the

Static Network

screen, “Static Fltr” will appear before the

network address of this entry.

Type

This field is only available when the

Setup

field is set to <

IPX Servers

>. The

Type

field

displays the Hex value assigned to each known server. When a service is added using

TRL

, a Hex value must be defined. If you wish to learn or filter certain services that match

a particular server type, manually add an entry specifying the desired Hex value. This setting
will enable the unit to learn or filter all services that match the specified service type. This field
may be used in conjunction with the

Name

field, described below. Range 1-FFFF.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands