Carrier Access Adit 600 User Manual Download Page 183

Page: 183 / 296

CMG Router - Release 2.7

6-9

Basic

Configuration

Remote Adit Profile

Remote Adit Profile

A screen will ask you if you would like to Add a Remote Adit Profile. Select

<YES>

and

NTER

]

The guide will walk through each Remote Profile that has been setup.

When exiting the last profile the guide will ask if you Each time you exit the last
Remote Profile the guide will ask you if you would like

Page Fields

Profile Name

Enter a unique name for this Remote Adit. Name can be up to 11 characters.

Protocol

Mode

- <Route>, <Blocked> and <Bridge>.

WAN Network Updates

- <Never>, <Periodic> and <Triggered>.

IPX

Mode

- <Blocked>, <Bridge> and <Optimized>.

WAN Network Updates

- <Never>, <Periodic>, <Triggered>.

Other

Mode

- <Blocked>, <Bridge> and <Optimized>.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands