Carrier Access Adit 600 User Manual Download Page 179

Page: 179 / 296

CMG Router - Release 2.7

6-5

Basic

Configuration

Routing Protocol/Security

Routing Protocol/Security

Page Fields

Direction(s) for LAN Network Updates

Selection is:

< Both>

<Neither>

<Send>

<Receive>

. Default is Neither.

RIP mode to be received from remotes

Selection is:

<RIP1>

<RIP2>

<RIP1/RIP2>

. Default is RIP 1.

RIP mode to send to remotes

Selection is:

<RIP1>

<RIP2>

<RIP1/RIP2>

. Default is RIP 1.

Protocol remotes will use to authenticate local LocalUnit

Selection is:

<CHAP>

<PAP>

<NONE>

. Default is None.

Change the CHAP Secret LocalUnit will send?

Note: this field displays only with a selection on

<CHAP>

Selection is:

<YES>

<NO>

. Below the current Secret Password is listed.

<YES>

is selected, the operator will be requested to enter in a new password, and retype this

password to confirm.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands