Carrier Access Adit 600 User Manual Download Page 142 | Manualshive

Page: 142 / 296

background image

5-10

CMG Router - Release 2.7

Profile Directory:Remote Profile

Remote (WAN) Profile

WAN IP

This field is used to enable the Adit to assign an IP Address to the remote device that
this remote profile is attached to.

Numbered

Designate if the local unit will have an IP Address assigned to the WAN when
communicating with this remote unit. If the remote unit is an Adit, it is recommended that
the WAN remain unnumbered, thus conserving IP Addresses. This field displays if the

IP

Mode

field is set to <

Route

>.

IP Address:

This address is used to uniquely identify the Adit unit on the

internetwork. Use this field to assign an IP Address to the WAN.

Subnet Mask:

A subnet mask determines which bits in the IP address are used to

identify the network number. It is also a method of extending the IP Network Address
so that a site may use one network address for several different networks.

Default Router

Use this field to identify a router that is physically connected to your LAN. If the Adit
receives a packet destined to a network that is not known, the packet will be sent to the
router identified in this field. This field is only displayed if the

IP

Mode

field is set to

<

Bridge

>.

«
...
140
141
142
143
144
...
»

Summary of Contents for Adit 600









































































































































































































































































































Reviews:

No comments

Related manuals for Adit 600

Brand: Ubiquiti Pages: 40

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Brand: D-Link Pages: 31

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

Brand: IDT Pages: 292

Brand: Cowfish Technologies Pages: 38

Brand: 1&1 Pages: 32

WNFB-265AXI(BT)

Brand: Sparklan Pages: 14

Brand: CalAmp Pages: 115

Brand: Compro Technology Pages: 2

Brand: Korenix Pages: 25

Brand: Patton electronics Pages: 2

Brand: iDirect Pages: 72

Brand: Alcatel-Lucent Pages: 154

Brand: WIN Enterprises Pages: 25

Brand: Alloy Pages: 13

Brand: Billion Pages: 2

Brand: Cambium Networks Pages: 292

Brand: Planet Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands