Carrier Access Adit 600 User Manual Download Page 84 | Manualshive

Page: 84 / 296

background image

3-46

CMG Router - Release 2.7

Profile Directory:Router Card Profile

Voice Channels

VOIP Algorithm Preference Order

- Defines the order preference of voice coding

algorithms for VoIP calls, on the specified voice channel(s). Up to 6 algorithms can be listed, in order
of preference. This list limits the acceptable codecs for a particular voice channel to those specified.
This can be used to limit voice channels that have a modem or fax machine attached to use only
G.711. Default settings list all algorithms, selections can be changed to none.

RFC2833 Options
Signals

<disable

> - Disable signaling in RTP payloads. Default.

<

abcd

> - Use

abcd

signaling in RTP payloads.

Payload Type

<default

> - Will be the value of the DTMF relay telephone event payload type. Default.

<

number

> - Range between 96-127.

Repeat Count

Set the number of initial RTP message repeats at the time of signal transition. Range is 0-10
repeats. Default is 2.
Note: a repeat of 2 times, in essence is a message, followed by 2 repeats.

Repeat Interval

Set the interval of RTP messages at the time of transition in milliseconds. Range is 1-50
milliseconds, with a default of 5.

Refresh Interval

Set the periodic refresh interval of RTP signaling states. Range is 500-4000 milliseconds, with
a default of 4000.

«
...
82
83
84
85
86
...
»

Summary of Contents for Adit 600









































































































































































































































































































Reviews:

No comments

Related manuals for Adit 600

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

12big Rack Fibre 8

Brand: LaCie Pages: 9

4-Port 10/100Mbps Ethernet Broadband Router

Brand: AOpen Pages: 41

Brand: ZyXEL Communications Pages: 422

Brand: Belkin Pages: 2

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Air Live GW-300R

Brand: Ovislink Pages: 20

EZ Switch SMC-EZ1024FDT

Brand: SMC Networks Pages: 4

JetNet 5720G-8P Series

Brand: Korenix Pages: 52

Brand: M-Audio Pages: 67

Brand: MikroTik Pages: 5

GigaSpire BLAST u6

Brand: Calix Pages: 9

Cradlepoint AER1600

Brand: Choose 2 rent Pages: 5

Brand: Crestron Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands