Carrier Access Adit 600 User Manual Download Page 118 | Manualshive

Page: 118 / 296

background image

4-32

CMG Router - Release 2.7

Profile Directory:Local Profile

DHCP Server/Client/Relay

DHCP Mode: <Server>

Info: <Active Leases>

Displays the Active Lease Information below.

Domain Name

This option is used if the DHCP Server is enabled on the DHCP Server/BOOTP Relay screen.
On a LAN network where the Adit is the DHCP Server, the

Domain Name

will be assigned

with IP addressing information to DHCP clients. This value is a maximum of 41 characters.

Start IP Address

If the Adit is specified to act as a DHCP server, enter the first valid IP Address the Adit may
assign to a DHCP client. This field acts in conjunction with the

Number

field.

Number

Enter the number of IP Addresses that this Adit unit may assign. This field acts in conjunction
with the

Start

IP

Address

field by using a contiguous block of IP Addresses. Number range is

1 through 254.

DHCP
Mode:
Server

«
...
116
117
118
119
120
...
»

Summary of Contents for Adit 600









































































































































































































































































































Reviews:

No comments

Related manuals for Adit 600

TokenLink Velocity 3C319

Brand: 3Com Pages: 2

Brand: Draytek Pages: 8

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: iDirect Pages: 72

Brand: PaloAlto Networks Pages: 28

McDATA Eclipse 1620

Brand: Sun Microsystems Pages: 9

Wireless Outdoor Bridge XI-1500-IH

Brand: IMC Networks Pages: 13

CNGE28FX4TX24MS2

Brand: Comnet Pages: 154

Brand: Baicells Pages: 38

Brand: Zmotion Pages: 57

BioSense Series

Brand: ZKTeco Pages: 96

Brand: 3Com Pages: 2

Brand: 3Com Pages: 8

AirProtect Enterprise Engine 6100

Brand: 3Com Pages: 12

Brand: 2Wire Pages: 20

Brand: 3Com Pages: 82

Brand: MSE Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands