Carrier Access Adit 600 User Manual Download Page 180

Page: 180 / 296

6-6

CMG Router - Release 2.7

Basic Configuration

Routing Protocol/Security

Change the PAP Secret LocalUnit will send?

Note: this field displays only with a selection on

<PAP>

Selection is:

<YES>

<NO>

. Below the current Secret Password is listed.

<YES>

is selected, the operator will be requested to enter in a new password, and retype this

password to confirm.

Authentication User ID

Selection is:

<Local Profile Name>

<Local Custom Name>

<Local Profile Name>

Displays the current Local Adit name.

<Local Custom Name>

With this selection you will be prompted to enter a Custom name. This

name can be up to 32 characters long.

Protocol LocalUnit will use to authenticate all remotes

Selection is:

<CHAP>

<PAP>

<NONE>

. Default is None.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands