Carrier Access Adit 600 User Manual Download Page 253

Page: 253 / 296

CMG Router - Release 2.7

A-5

User

Events

Alarms

Alarms

Data integrity fault detected and corrected

This is logged when the unit detects and recovers from a loss of data
synchronization.

Dedicated trunk connection on Port

“X”

lost

Description

[Local LAN,

“remote”

] [IPX SAP, IPX RIP] [

“server name”,“network”

] exists at

[Local LAN,

“remote”

]

MAC Address Table is full

Triggered 802.3 IPX (Eth II IP) network update to

“remote”

fail

Triggered 802.3 IPX server update to

“remote”

fail

WAN data loss detected, recovery action taken

This is logged when the unit begins the recovery process from trunks with high
error conditions.

[Pass, Drop] [dyn] [Any, Protocol=xx,Type=xx,Port=xx] [to, from] <

rem sys

Firewall Rule <

rule num

NOTE:

All alarms generate SNMP traps.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands