Carrier Access Adit 600 User Manual Download Page 189

Page: 189 / 296

CMG Router - Release 2.7

7-3

Verification

Window

Ping Utility

2. Press

NTER

]

. The

LAN Port Verification

window will display.

3. To initiate a Ping, select

START PING <Single Ping >

, scroll to

<Continuous Ping>

and select

NTER

]

. The Ping process will begin.

LAN Port Tests Fields

Dst Host

Destination Host. The Destination Address of the host to be tested.

Access Port

This is the local or remote profile of the network used during the test. The operator can scroll
(with the

PACEBAR

]

) through the selections of the

Access Port: <Local LAN>

to select the

Local LAN

or any of the defined

Remote Unit(s)

. All defined Remote Profiles will be in this

selection.

Src IP Address

Source IP Address. This is one of the multiple IP addresses assigned to the Ethernet LAN port
and will override the IP address that will be used as the source IP address. Default is to use the
IP address of the interface from which the ping is sent.

Payload

This optional parameter sets the number of bytes to send in the ICMP echo request payload.
Range is 0 - 8000, default is 56.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands