Carrier Access Adit 600 User Manual Download Page 285 | Manualshive

Page: 285 / 296

background image

CMG Router - Release 2.7

Glossary - 7

Glossary

RSIP

Realm-Specific Internet Protocol. RSIP is an IP address translation
technique that is an alternative to NAT. RSIP lets an enterprise safeguard
many private Internet addresses behind a single public Internet address.

RTCP

Real-Time Conferencing Protocol. Supports real-time conferencing for
large groups on the internet. It has source identification and support for
audio and video bridges/gateways. Supports multicast-to-unicast
translators.

RTP

Realtime Transport Protocol. An IETF standard for streaming realtime
multimedia over IP in packets. Supports transport of real-time data like
interactive voice and video over packet switched networks.

SDP

Session Description Protocol. SDP is intended for the description of
multimedia sessions over IP-based networks. Defined in RFC2327.

SNAP

Subnet Access Protocol. A version of the IEEE local area network logical
link control frame similar to the more traditional data link level
transmission frame that lets you use nonstandard higher-level protocols.

SNMP

Simple Network Management Protocol. SNMP is the most common
method by which network managements applications can query a
management agent using a supported MIB (Management Information
Base). SNMP operates at the OSI application layer.

Spanning Tree
Protocol

Spanning Tree Protocol is a link management protocol that provides path
redundancy while preventing undesirable loops in the network. For an
Ethernet network to function properly, only one active path can exist
between two stations.

T1

Trunk Level 1. A digital transmission link with a total signaling speed of
1.544 Mbps. T1 is a standard for the digital transmission in North
America.

Terminal Access Controller Access Control System.

«
...
283
284
285
286
287
...
»

Summary of Contents for Adit 600









































































































































































































































































































Reviews:

No comments

Related manuals for Adit 600

Brand: ZETR Pages: 2

Brand: CallDirect Pages: 33

Brand: Nayar Systems Pages: 37

DR-4100P Series

Brand: Idis Pages: 30

Brand: Magnadyne Pages: 13

Storagelibrary T24

Brand: Tandberg Data Pages: 28

FieldPoint cFP-RTD-122

Brand: National Instruments Pages: 15

RS-232/422/485 Serial Card CE 3PXCC4A

Brand: B&B Electronics Pages: 47

Brand: Schrack Technik Pages: 2

Speedway Revolution

Brand: impinj Pages: 60

Brand: Moxa Technologies Pages: 2

Brand: AMX Pages: 2

Brand: Lanner Pages: 59

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Brand: AMX Pages: 1

Brand: 3Com Pages: 12

Brand: HMS Pages: 18

Brand: Ryobi Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands