Carrier Access Adit 600 User Manual Download Page 184

Page: 184 / 296

6-10

CMG Router - Release 2.7

Basic Configuration

Remote Adit Profile

Does this unit have a numbered IP address assigned on the WAN?

Selection is:

<Yes>

<No>

. If

<Yes>

is selected IP Address and Subnet Mask below are listed.

IP Address

Enter the IP Address of the Remote Adit.

Subnet Mask

Enter the Subnet Mask of the above IP Address.

Select WAN Port Number

Selection is:

<None>

<1>

through

<24>

(all existing WAN ports are listed).

Connection

Displays the connection information for the selected WAN in the form {slot:port:channel}.

WAN Connection Type

Displays the WAN connection type (PPP, Frame Relay 1490 or PPP in Frame Relay).

DLCI

Enter the Data Link Connection Identifier. Range is between 16-1022.

Note: This field is not available with a WAN that has PPP set as it’s connection type.

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands